AN EASY TUTORIAL FOR BATHTUB INSTALLATION

An Easy Tutorial for Bathtub Installation

An Easy Tutorial for Bathtub Installation

Blog Article

Get Started

What're your opinions about How to Install a Bathtub?


How to Install a Bathtub Yourself
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as often, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily accessible, the job can move speedily; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to move out the old tub and also set in the new one. See to it you have actually certified on your own for the task as well as are comfortable trying it. Instead of hiring a professional to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have actually already acquired a new tub and don't need to transform the arrangement of your previous supply of water pipelines.
Your devices and material checklist must consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be fairly bothersome as a result of the limited gain access to that is typically the case.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. When the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
    Before carrying on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
    If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, position the faucet in the mounting opening in the bath/basin making sure that the washing machines are in location in between the faucet and also the sink. Secure the tap in place with the supplier given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Installing the Bath tub


    Utilizing the two wood boards under its feet, put the bathtub in the called for position. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
    The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the bath tub until the spirit level reviews degree.
    To install taps, fit the bottom of the outermost adaptable tap connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
    Switch on the water as well as inspect all joints as well as new pipework for leakages and also tighten them if necessary. Fill up the bathtub and likewise examine the overflow electrical outlet and the typical outlet for leakages.
    Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait up until the bathtub has actually been made use of at the very least when as this will settle it into its last setting.

    Planning for the Installment


    Firstly, the supporting framework supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to stop strain on the bath tub.
    Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.

    Tiling Around the Bath tub


    In the area where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split an inflexible seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, leading to difficulties with moisture and possible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to always load the tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into consideration this motion before sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof glue and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    We had been shown that report about How to Install a Bathtub Yourself through someone on another web address. Loved our blog posting? Please share it. Help other people check it out. Thank-you for your time spent reading it.


    Quality assurance? Connect.

    Report this page